All Articles Logic Pro
Creación de viento FX: filtro de ruido en la lógica del uso de ES1
Richard Lainhart on Fri, June 10th | 0 comments
In this Quick Tutorial, we'll look at how to create a classic analog synthesis sound — the sound of whistling wind — using Logic's ES1 synth.

En este rápido tutorial, veremos cómo crear un sonido clásico de la síntesis analógica del sonido de silbido del viento utilizando la lógica del sintetizador ES1.


Paso 1 - Lanzamiento ES1

Comience abriendo la lógica y seleccionando Archivo


Luego, en la sección de E / S del canal en la parte inferior izquierda del Inspector, haga clic y mantenga en el instrumento por defecto Software EVP88 y elegir ES1


Por último, haga doble clic en el botón azul ES1 para abrir la ventana ES1:


Paso 2 - Configurar ES1

Configure la ES1, como se muestra en la siguiente imagen:


Aquí está una lista de todos los valores esenciales, de izquierda a derecha y de arriba abajo, y lo que significan:

  • Mix is set to Sub only, because the Sub oscillator is the only one of the two that offers white noise. 
  • The Sub oscillator is set to Noise (the squiggly waveform). 
  • Drive is set to 0 (zero) to reduce distortion. 
  • Filter is set to '24dB classic' for the classic swept noise sound. 
  • The filter's Cutoff is set to about the middle position, but you can adjust that to taste. 
  • Resonance is also set to about the middle position. The increased Resonance is what gives you a sense of pitch and "whistly-ness" in the final sound. You can also adjust this to taste, but don't set it too high or it will self-resonate and provide too much of a sense of pitch. 
  • Key is set to the middle position, so that playing further up the keyboard will open the filter up a bit more and let you stack up multiple wind voices in different registers. 
  • In the bottom section, the Low Frequency Oscillator is set to a smoothed random waveform (the one at the 3 o'clock position), itself derived from white noise. Applying this to the Filter Cutoff will automatically vary the wind's pitch. Rate is set to 0.62 Hz; feel free to adjust this also. Higher frequencies will give you more active wind.
  • The slider to the left of the Router is set to the upper 3/4 of its range; this controls the basic amount of the Low Frequency Oscillator that is sent to control the filter's cutoff. In the Router itself, the filter's Cutoff is set as the destination for the Low Frequency Oscillator. 
  • The slider to the right of the Router is set to the lower 1/6 of its range; this sends a little more of the Low Frequency Oscillator to the filter's cutoff depending on your keyboard's trigger velocity.
  • Finally, the ADSR sliders are all set to Long or Full, or nearly so; this will give you long slow attacks and decays for your wind sound.


Paso 3 - Conclusión

Ahora toca un par de notas en el teclado MIDI en la mitad de su rango, y se oirá un sonido de viento invernal convincente. Pruebe a añadir una reverb larga de Space Designer para obtener un sonido aún ghostlier:

[Audio id = "6749"]


Y, como siempre, experimentar y divertirse en la lógica !



Comments (0)

You must be logged in to comment. Login Now

Feedback
Course Advisor
Don't Know Where To Start?
Ask A Course Advisor
Ask Us!
Copy the link below and paste it into an email, forum, or Facebook to share this with your friends.
Make money when you share our links
Become a macProVideo.com Affiliate!
The current affiliate rate is: 50%
Classes Start Next Week!
Live 8-week Online Certification Classes for: