All Articles Logic Pro
ES1を使用したロジックでノイズフィルタ:風FXを作成する
Richard Lainhart on Fri, June 10th | 0 comments
In this Quick Tutorial, we'll look at how to create a classic analog synthesis sound — the sound of whistling wind — using Logic's ES1 synth.

このクイックチュートリアルでは、我々は使用して風ぴゅうぴゅうクラシックなアナログシンセのサウンドを作成する方法を見ていきますロジックの ES1シンセを。


ステップ1 - 起動ES1

ロジックを開き、 ファイルを選択して起動します。


その後、インスペクタの左下のチャンネルストリップのI / Oセクションで、クリックして、デフォルトEVP88ソフトウェア音源でホールドし、ES1を選択します。


ついに、ES1ウインドウを開くには青いES1ボタンのダブルクリック:


ステップ2 - ES1の設定

次のスクリーンショットに示すようにES1を設定します。


ここでは、左から右、上から下に、あらゆる基本設定のリストです、そしてそれらの意味:

  • Mix is set to Sub only, because the Sub oscillator is the only one of the two that offers white noise. 
  • The Sub oscillator is set to Noise (the squiggly waveform). 
  • Drive is set to 0 (zero) to reduce distortion. 
  • Filter is set to '24dB classic' for the classic swept noise sound. 
  • The filter's Cutoff is set to about the middle position, but you can adjust that to taste. 
  • Resonance is also set to about the middle position. The increased Resonance is what gives you a sense of pitch and "whistly-ness" in the final sound. You can also adjust this to taste, but don't set it too high or it will self-resonate and provide too much of a sense of pitch. 
  • Key is set to the middle position, so that playing further up the keyboard will open the filter up a bit more and let you stack up multiple wind voices in different registers. 
  • In the bottom section, the Low Frequency Oscillator is set to a smoothed random waveform (the one at the 3 o'clock position), itself derived from white noise. Applying this to the Filter Cutoff will automatically vary the wind's pitch. Rate is set to 0.62 Hz; feel free to adjust this also. Higher frequencies will give you more active wind.
  • The slider to the left of the Router is set to the upper 3/4 of its range; this controls the basic amount of the Low Frequency Oscillator that is sent to control the filter's cutoff. In the Router itself, the filter's Cutoff is set as the destination for the Low Frequency Oscillator. 
  • The slider to the right of the Router is set to the lower 1/6 of its range; this sends a little more of the Low Frequency Oscillator to the filter's cutoff depending on your keyboard's trigger velocity.
  • Finally, the ADSR sliders are all set to Long or Full, or nearly so; this will give you long slow attacks and decays for your wind sound.


ステップ3 - 結論

今、その範囲の途中でMIDIキーボードでノートのカップルを再生し、説得力のある冬の風の音が聞こえるはずです。さらにghostlier音のためのSpace Designerから長いリバーブを追加してみてください。

[オーディオのid ="6749"]


そして、いつものように、実験との楽しい持っているロジックを



Comments (0)

You must be logged in to comment. Login Now

Feedback
Course Advisor
Don't Know Where To Start?
Ask A Course Advisor
Ask Us!
Copy the link below and paste it into an email, forum, or Facebook to share this with your friends.
Make money when you share our links
Become a macProVideo.com Affiliate!
The current affiliate rate is: 50%
Classes Start Next Week!
Live 8-week Online Certification Classes for: