All Articles Logic Pro
바람 FX 만들기 : 소음이 ES1 사용 로직 필터링
Richard Lainhart on Fri, June 10th 0 comments
In this Quick Tutorial, we'll look at how to create a classic analog synthesis sound — the sound of whistling wind — using Logic's ES1 synth.

이 빠른 튜토리얼에서 우리는 고전적인 아날로그 합성음을 이용하여 바람을 휘파람 소리 만드는 방법에 대해 살펴보겠습니다 로직의 ES1 synth합니다.

1 단계 - 실행 ES1

논리를 열고 파일을 선택하여 시작

그 다음, 검시관의 왼쪽 하단에 채널 스트립의 I / O 섹션에서 클릭하고 기본 EVP88 소프트웨어 악기 잡고 ES1을 선택

마지막으로 ES1 창을 엽니다 파란색 ES1 버튼을 두 번 클릭합니다 :

2 단계 - ES1를 설정

아래의 스크린샷에 표시된 ES1을 구성합니다 :

다음은 왼쪽에서 오른쪽 아래로 위로, 모든 필수적인 설정의 목록, 그들은 무슨 뜻 :

  • Mix is set to Sub only, because the Sub oscillator is the only one of the two that offers white noise. 
  • The Sub oscillator is set to Noise (the squiggly waveform). 
  • Drive is set to 0 (zero) to reduce distortion. 
  • Filter is set to '24dB classic' for the classic swept noise sound. 
  • The filter's Cutoff is set to about the middle position, but you can adjust that to taste. 
  • Resonance is also set to about the middle position. The increased Resonance is what gives you a sense of pitch and "whistly-ness" in the final sound. You can also adjust this to taste, but don't set it too high or it will self-resonate and provide too much of a sense of pitch. 
  • Key is set to the middle position, so that playing further up the keyboard will open the filter up a bit more and let you stack up multiple wind voices in different registers. 
  • In the bottom section, the Low Frequency Oscillator is set to a smoothed random waveform (the one at the 3 o'clock position), itself derived from white noise. Applying this to the Filter Cutoff will automatically vary the wind's pitch. Rate is set to 0.62 Hz; feel free to adjust this also. Higher frequencies will give you more active wind.
  • The slider to the left of the Router is set to the upper 3/4 of its range; this controls the basic amount of the Low Frequency Oscillator that is sent to control the filter's cutoff. In the Router itself, the filter's Cutoff is set as the destination for the Low Frequency Oscillator. 
  • The slider to the right of the Router is set to the lower 1/6 of its range; this sends a little more of the Low Frequency Oscillator to the filter's cutoff depending on your keyboard's trigger velocity.
  • Finally, the ADSR sliders are all set to Long or Full, or nearly so; this will give you long slow attacks and decays for your wind sound.

3 단계 - 결론

이제 그 범위의 중간에 MIDI 키보드에서 음표 몇 곡 연주, 당신은 설득력 겨울 바람 소리가해야합니다. 도 ghostlier 사운드 공간 디자이너에서 긴 reverb를 추가해보십시오 :

[오디오 ID = "6749"]

그리고 언제나처럼, 실험 및 재미를 보지 로직을 !

Related Videos
Comments (0)

You must be logged in to comment.

Mixing and Automation
Cubase 10 104
Dream It. Do It.
Do you want to learn Mixing and Automation?
Yes, I want to learn!
No Thanks, I just want to read the article.
Course Advisor
Don't Know Where To Start?
Ask A Course Advisor
Ask Us!
Copy the link below and paste it into an email, forum, or Facebook to share this with your friends.
Make money when you share our links
Become a Affiliate!
The current affiliate rate is: 50%
Classes Start Next Week!
Live 8-week Online Certification Classes for: