I very much doubt that when Tadao Kikumoto designed Roland's TB-303 in the early 80s, he knew that he would be starting a cultural revolution! On its release in 1981...
내가 타다오 Kikumoto가 초기 80 롤랜드 TB - 303을 설계했을 때, 그는 문화 혁명을 시작 될 것을 알고 너무나 의심! 가수와 작곡가에 대한 간단한베이스 라인 반주 상자위한 1981 제품이 출시된,시,
그렇다면 1987 년, Phuture라는 시카고 기반의 의상은 산성 트랙과 산성 하우스가 태어난라는 트랙을 발표했다. TB - 303은 노래를 정의 소리 였어요! Squelchy, 공진 왜곡과 반복.
이후 그것은 팝에서 힙합으로 기록 수천 수만 문자 그대로, 주변에 전기 반석 위에 등장했다. 그리고 그것은 아직 건제하다!
Trilian에서 TB - 303을 에뮬레이트
사용할 수있는 303의 일부 우수한 전용 소프트웨어와 하드웨어 에뮬레이션은 물론있다 (당신은 일본 설명서, 원본에 2,000 달러 지출 싶진 않겠지 경우 !!!).
그것은 Spectrasonics '파워 하우스베이스 synth의 한를 달아야하지만 정말 쉽습니다 Trilian 하고, 프로그램을 더 쉽게. 그리고 그것도 아주 좋은 소리! 하자 그것을 해!
1 단계 - 파형
Trilian를 열고 편집 창을 선택합니다. 브라우저를 열 패널의 중앙에 Soundsource 이미지를 클릭하십시오.
Navigate down the Source list to Roland TB-303 and select the waveform called TB-303 Sawtooth.
Half the battle is already won as Spectrasonics has lovingly sampled the waveforms from the original model, which does have quite a distinctive sound.
2 단계 - 봉투
Go back to the Edit window and set the Amp and Filter envelopes like so:
On both envelopes, turn down the Velocity ('VELO') knob to 0%. Done!
3 단계 - 필터
Turn the Filter section On and load in the 'LPF Juicy 24db' Lowpass from the drop down menu. Set the ENV amount to 0%.
4 단계 - 음성 제어
Now it’s time to set up the Voice Controls for the sound. These are on the right-hand side of the Edit window. Set them up like this:
The sound is monophonic so I’ve enabled Solo (in Legato mode, the tiny 'L' to the left of the Solo button) with 'Voices' set to 1 (to be on the safe side!). The 'Oct' is set to 0, and the 'Gain' to -6 db.
The Glide is on (again, in Legato mode) for Layer A with a time of 9ms. I found this to be the optimum time setting when comparing against other 303 clones.
Solo and Glide are very important as they affect how the Note triggering, Envelopes and Portamento effect work on overlapping notes.
5 단계 - 순서를 프로그래밍
How you program your sequence will affect how the 303 sound will work. The TB-303 has two kinds or notes, short and tied.
Short notes I found have a length of about 2/3 of a 16th-note. The gap between them, apart from sounding right ensures that the sample is re-triggered, as well as the Filter envelope.
Any longer notes you program should have this gap at the end, too. Long notes on a 303 are made by putting two notes of the same value one after the other and enabling Glide to the first note. This ties them together to make one note.
On the 303 you will only hear the Portamento Glide effect if the two ‘tied’ notes have different pitches. In a sequencer this is done by overlapping notes. You can hear this in the example below.
The time we set for the Glide (9ms) is constant so the farther away from each other the notes are, the more extreme the effect.
These overlapping notes also serve to prevent the sample re-triggering from the start (Solo mode) and also stop the Filter envelope from re-triggering. The Glide and Filter envelope are two trademark sounds of the 303.
Here’s a sequence I’ve put together. It has short, long and overlapping notes. Here it is with the Filter set to 1370 kHz. You can copy it or make your own to test the sound.
Not bad, eh?
6 단계 - 메인 컨트롤에 매개 변수를 지정
Before we start to tweak this sound I’m going to assign the parameters I need for the Patch to do its thing to the Macros in the Main Controls page. This just makes it easier to reuse the Patch later and looks cool as well!
If you switch to Main you’ll see the default Controls mapping. These are dead easy to change. First, I’m going to map the Filter's Cutoff.
Before you assign a new parameter to the control it’s a good idea to clear it as it will already have parameters assigned to it. If you don't, your new parameter will be added to the list which could cause some problems later.
Control-Click on the Cutoff knob and choose 'Clear all parameter assignments for this control'.
Now Control-Click again and choose 'Assign this control to the next touched audio control'. Go to the Edit page and click Cutoff in the Filter section.
Rename the new assignment CUTOFF.
Repeat these steps with the Filter Resonance (RESONANCE), Envelope Depth (ENV MOD) and Filter Decay (ENV DECAY) parameters.
Now I’m going to assign these Controls to a Group. I do this by clicking and dragging left on the the far right corner of the separator bars. A new Group is created called 'Group 2'. We’ll use it later.
You can now assign these hardware MIDI faders by Control-Clicking on each knob and choosing 'MIDI CC Learn'. You could also use your host's automation assignments for these, too. In Logic, for example, it's the Controller Assignments window.
Now I’m all hooked up, and I'm ready to record some tweaking. Here’s a quick example. I’m just playing with CUTOFF, RESONANCE, ENV MOD and ENV DECAY parameters.
That’s about it for the basic setup. Save out your Patch. Don’t forget you can always use the TB-303 Square waveform by simply switching to it in the Soundsource window.
7 단계 - 효과 추가
You can go a step further and add Distortion and Delay to make a more aggressive 303 Patch if you like. Here’s a setup I made for mine:
And here's how I’ve assigned the parameters to the Main Controls:
The result is pretty hardcore!
So that’s it! A TB-303 in Trilian. The only thing you need now is a large field to stand in and some glow sticks!